Engineering Practices Laboratory detail syllabus for Computer & Communication Engineering (C&C), 2017 regulation is taken from Anna University official website and presented for students of Anna University. The details of the course are: course code (GE8261), Category (ES), Contact Periods/week (4), Teaching hours/week (0), Practical Hours/week (0). The total course credits are 4.
For all other c&c 2nd sem syllabus for be 2017 regulation anna univ you can visit C&C 2nd Sem syllabus for BE 2017 regulation Anna Univ Subjects. The detail syllabus for engineering practices laboratory is as follows.”
Course Objective:
- To provide exposure to the students with hands on experience on various basic engineering practices in Civil, Mechanical, Electrical and Electronics Engineering.
- Residential house wiring using switches, fuse, indicator, lamp and energy meter.
- Fluorescent lamp wiring.
- Stair case wiring
- Measurement of electrical quantities – voltage, current, power and power factor in RLC circuit.
- Measurement of energy using single phase energy meter.
- Measurement of resistance to earth of an electrical equipment.
- Study of Electronic components and equipments – Resistor, colour coding measurement of AC signal parameter (peak-peak, rms period, frequency) using CR.
- Study of logic gates AND, OR, EX-OR and NOT.
- Generation of Clock Signal.
- Soldering practice – Components Devices and Circuits – Using general purpose PCB.
- Measurement of ripple factor of HWR and FWR.
GROUP A (CIVIL and MECHANICAL)
I CIVIL ENGINEERING PRACTICE 13
Buildings:
(a) Study of plumbing and carpentry components of residential and industrial buildings. Safety aspects.
Plumbing Works:
(a) Study of pipeline joints, its location and functions: valves, taps, couplings, unions, reducers, elbows in household fittings.
(b) Study of pipe connections requirements for pumps and turbines.
(c) Preparation of plumbing line sketches for water supply and sewage works.
(d) Hands-on-exercise:
Basic pipe connections – Mixed pipe material connection – Pipe connections with different joining components.
(e) Demonstration of plumbing requirements of high-rise buildings.
Carpentry using Power Tools only:
(a) Study of the joints in roofs, doors, windows and furniture.
(b) Hands-on-exercise:
Wood work, joints by sawing, planing and cutting.
II MECHANICAL ENGINEERING PRACTICE 18
Welding:
(a) Preparation of butt joints, lap joints and T- joints by Shielded metal arc welding.
(b) Gas welding practice
Basic Machining:
(a) Simple Turning and Taper turning
(b) Drilling Practice
Sheet Metal Work:
(a) Forming and Bending:
(b) Model making – Trays and funnels.
(c) Different type of joints.
Machine assembly practice:
(a) Study of centrifugal pump
(b) Study of air conditioner
Demonstration on:
(a) Smithy operations, upsetting, swaging, setting down and bending. Example -Exercise – Production of hexagonal headed bolt.
(b) Foundry operations like mould preparation for gear and step cone pulley.
(c) Fitting – Exercises – Preparation of square fitting and V – fitting models.
GROUP B (ELECTRICAL and ELECTRONICS)
III ELECTRICAL ENGINEERING PRACTICE 13
IV ELECTRONICS ENGINEERING PRACTICE 16
Course Outcome:
On successful completion of this course, the student will be able to
- Fabricate carpentry components and pipe connections including plumbing works.
- Use welding equipments to join the structures.
- Carry out the basic machining operations
- Make the models using sheet metal works
- Illustrate on centrifugal pump, Air conditioner, operations of smithy, foundary and
- fittings
- Carry out basic home electrical works and appliances
- Measure the electrical quantities
- Elaborate on the components, gates, soldering practices.
List of Equipment for a Batch of 30 Students: Civil
- Assorted components for plumbing consisting of metallic pipes, plastic pipes, flexible pipes, couplings, unions, elbows, plugs and
- Carpentry vice (fitted to work bench) 15 Nos.
- Standard woodworking tools 15 Sets.
- Models of industrial trusses, door joints, furniture joints 5 each
- Power Tools: (a) Rotary Hammer 2 Nos
- Arc welding transformer with cables and holders 5 Nos.
- Welding booth with exhaust facility 5 Nos.
- Welding accessories like welding shield, chipping hammer,
- Oxygen and acetylene gas cylinders, blow pipe and other
- Centre lathe 2 Nos.
- Hearth furnace, anvil and smithy tools 2 Sets.
- Moulding table, foundry tools 2 Sets.
- Power Tool: Angle Grinder 2 Nos
- Study-purpose items: centrifugal pump, air-conditioner One each.
- Assorted electrical components for house wiring 15 Sets
- Electrical measuring instruments 10 Sets
- Study purpose items: Iron box, fan and regulator, emergency lamp 1 each
- Megger (250V/500V) 1 No.
- Power Tools: (a) Range Finder 2 Nos
- Soldering guns 10 Nos.
- Assorted electronic components for making circuits 50 Nos.
- Small PCBs 10 Nos.
- Multimeters 10 Nos.
- Study purpose items: Telephone, FM radio, low-voltage power supply
other fittings. 15 Sets.
(b) Demolition Hammer 2 Nos
(c) Circular Saw 2 Nos
(d) Planer 2 Nos
(e) Hand Drilling Machine 2 Nos
(f) Jigsaw 2 Nos
MECHANICAL
wire brush, etc. 5 Sets.
welding outfit. 2 Nos.
ELECTRICAL
(b) Digital Live-wire detector 2 Nos
ELECTRONICS
For detail syllabus of all other subjects of BE C&C, 2017 regulation do visit C&C 2nd Sem syllabus for 2017 Regulation.
Dont forget to download iStudy for latest syllabus and results, class timetable and more.