Devices and Machines Laboratory detail syllabus for Electronics & Instrumentation Engineering (Eie), 2017 regulation is taken from Anna University official website and presented for students of Anna University. The details of the course are: course code (EI8461), Category (PC), Contact Periods/week (4), Teaching hours/week (0), Practical Hours/week (0). The total course credits are 4.
For all other eie 4th sem syllabus for be 2017 regulation anna univ you can visit Eie 4th Sem syllabus for BE 2017 regulation Anna Univ Subjects. The detail syllabus for devices and machines laboratory is as follows.”
Course Objective:
- To facilitate the students to study the characteristics of various semiconductor devices.
- To provide practical knowledge on the analysis of regulators, amplifiers and oscillators.
- To obtain the no load and load characteristics of D.C machines.
- To obtain the speed characteristics of D.C motor.
- To find out regulation characteristics of Transformer.
List of Experiments for Devices Lab
- Simulation and experimental Characteristion of Semiconductor diode and Zener diode.
- Simulation and experimental Characteristion of a NPN Transistor under common emitter configurations.
- Simulation and experimental Characterisation of FET and JFET(Draw the equivalent circuit)
- Simulation and experimental Characterisation of UJT and generation of saw tooth waveforms
- Simulation and experimental Characterisation of RC and LC phase shift oscillators.
- Simulation and experimental Characterisation of Monostable and Astable multivibrators.
- Simulation of passive filters.
- Simulation of Single Phase half-wave and full wave rectifiers with inductive and capacitive filters.
- Characteristics of SCR and application as a controlled rectifier.
Minimum of Five Experiments To be Offered From the List. Additional One or Two Experiments Can be Framed Beyond the List or Curriculum
List of Experiments for Machines Lab
- Open circuit characteristics of D.C. shunt generator.
- Load characteristics of D.C. shunt generator.
- Load test on D.C. shunt motor.
- Speed control of D.C. shunt motor.
- Open circuit and short circuit tests on single phase transformer (Determination of equivalent circuit parameters).
- Load test on single phase induction motor.
Minimum of Five Experiments To be Offered From the List. Additional One or Two Experiments Can be Framed Beyond the List or Curriculum
Course Outcome:
- Gain knowledge on the proper usage of various electronic equipment and simulation tools for design and analysis of electronic circuits.
- Get hands-on experience in studying the characteristics of semiconductor devices.
- Ability to analyze various electronic circuits such as voltage regulators, transistor amplifiers and oscillators.
- Ability to make use of basic concepts to obtain the no load and load characteristics of D.C machines.
- Analyze and draw conclusion from the characteristics obtained by conducting experiments on machines.
- Ability to carry out the Experiments in batches to motivate the Team work.
List of Equipment for a Batch of 30 Students:
For Devices Lab:
S.No Name of the Equipment / Components
- Circuit Simulation Software ( 5 Users ) (Pspice / Matlab /other Equivalent software Package) with PC.
- Sufficient number of power supply, Galvanometer, Bread board, Multimeter, resistors, Decade Capacitance box, Decade resistance box, Decade Inductance box, CRO.
- Semiconductor devices like Diode, Zener Diode, NPN Transistors, JFET, and UJT.
For Machines Lab:
S.No Name of the Equipment / Components Quantity Required
- DC Shunt Motor with Loading Arrangement 3
- Single Phase Transformer 3
- Single Phase Induction Motor with Loading Arrangement 1
- Single Phase Auto Transformer 3
- Single Phase Resistive Loading Bank 2
- Sufficient number of Ammeters, Voltmeters, (or multimeters), switches, tachometers, Wattmeters. 2
For detail syllabus of all other subjects of BE Eie, 2017 regulation do visit Eie 4th Sem syllabus for 2017 Regulation.
Dont forget to download iStudy for latest syllabus and results, class timetable and more.