Industrial Automation detail TNDTE Diploma syllabus for Automobile Engineering (AU), M scheme is extracted from TNDTE official website and presented for diploma students. The course code (32152), and for exam duration, Teaching Hr/week, Practical Hr/week, Total Marks, internal marks, theory marks, duration and credits do visit complete sem subjects post given below. The syllabus PDFs can be downloaded from official website.
For all other automobile 5th sem syllabus for diploma m scheme tndte you can visit Automobile 5th Sem Syllabus for Diploma M Scheme TNDTE Subjects. The detail syllabus for industrial automation is as follows.
Rationale:
Impart knowledge about the automation process in the automobile industries. To acquire knowledge about the hydraulic and pneumatic systems and its functions of the components. Understand the control methods of automation.
Objectives:
- To learn the types of chassis and axles.
- To study about the steering system and its methods.
- To understand the suspension systems and its components.
- To learn the functions of universal joint and propeller shafts.
- To study working principle of differential unit.
- To learn about the types of brakes and tyres.
- To know the function of clutch and gear box and its types
Unit I
For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.
Unit II
Control Valves and Circuits
Pressure Control Valves (PCV):
Simple pressure relief valve, Compound pressure relief valve, Pressure reducing valve, Unloading valve, Sequence valve, Counter balance
valve.
Flow Control Valves (FCV):
Orifice as flow control valve, Needle valve, Pressure compensated and Non-pressure compensated valve.
Direction Control Valves (DCV):
Check valve, Pilot operated check valve, three-way valve, four-way valve: Manual/Mechanical/Solenoid operated valves. Servo valves:
Definition – Mechanical-hydraulic servo valve – Electro-hydraulic servo valves.
Accumulators:
Reservoirs and accumulators – Types of accumulators -Charging and discharging of accumulators – Accumulator circuits.
Deceleration circuit –
Intensifier circuit – Regenerative circuit – Synchronizing circuit – Automatic cylinder reciprocating circuit – Sequencing circuit.
Safety Circuits:
Two-hand safety control circuit – Fail-safe control circuit by using emergency cut-off valve.
Unit III
Selection of devices
Selection of Hydraulic Cylinder:
Speed of a hydraulic cylinder – Cylinder thrust – Acceleration and deceleration of cylinder loads – Local deceleration -Cylinder cushioning –
Cylinder preferred sizes – Piston rod buckling.
Selection of Hydraulic Motor:
Hydro-static drives – Hydro-static drive characteristics – Braking of hydrostatic drives – Matching motor to load.
Selection of Control Valves:
Relief valves – Flow control valves – Direction control valves.
Selection of Other Devices:
Seals and its classification – Filters and its types – Filter location. Selection of filters – Selection of conduits – tubing and hoses -Selection of pump – Pressure losses – Reservoir and its design – Sizing of accumulator.
Unit IV
For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.
Unit V
Programmable Logic Controller
Introduction to PLC – evolution – advantages – criteria for selection of suitable PLC – Block diagram of PLC – Programming devices – programming methods – STL and CSF, FBD and Ladder methods – simple instructions -programming NC and NO contacts – timer instructions – on-delay and off-delay timer – converting simple relay ladder diagram into PLC relay ladder diagram -PID and PWM functions. Simple PLC implementations for automatic star-delta starter and 4 floor lift system. Introduction and brief history of SCADA -hardware and software
Text Books:
- Pneumatic Systems Principles and Maintenance, S.R. Majumdar – Tata McGraw Hill Pub co
- Introduction to Programmable Logic Controllers, Gary Dunning – Thomson Delmar Learning Second Edition Second reprint 2003
Reference Book
For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.
For detail syllabus of all other subjects of BE Automobile, M scheme do visit Automobile 5th Sem syllabus for M scheme.
Dont forget to download iStudy Syllabus App for latest syllabus and results, class timetable and more.