Technical Drawing Computer Science 1st Sem BTEUP Syllabus 2019-2020

Technical Drawing detail BTEUP syllabus for Computer Science And Engineering, effective from 2019-2020, is collected from BTEUP 2017 Syllabus official website and presented for diploma students. PDF download is possible from official site but you can download the istudy mobile app for syllabus on mobile. The course details such as exam duration, Teaching Hr/week, Practical Hr/week, Total Marks, internal marks, theory marks, duration and credits do visit complete sem subjects post given below. The syllabus PDFs can be downloaded from official website.

For all other bteup syllabus 1st sem computer science 2019-2020 you can visit BTEUP Syllabus 1st Sem Computer Science 2019-2020 Subjects. The detail syllabus for technical drawing is as follows.

Rationale:

The course is aimed at developing basic graphic skills so as to enable them to use these skills in preparation of engineering drawings, their reading and interpretation. Understand the fundamentals of Engineering Drawing. Read and interpret object drawings.

Learning Outcomes:

After undergoing the subject, the students will be able to:

• Draw orthographic projections of different objects.
• Visualize three dimensional objects and draw Isometric Projections.
• Use the techniques and able to interpret the drawing in Engineering field.
• Draw exploded views of components & assemblies in preparation of service drawing. Draw free hand sketches of the schematic diagrams of electronic circuits, using standard symbols. Prepare drawing from the rough sketches provide and/or enlarge/reduce the given drawing to the desired scale.

1. Drawing Instruments and their uses

For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.

2. Active Devices

Semiconductor : Rectifier diode, Zener diode, Varacter diode, Tunnel diode, Photo, Light emitting diode (LED), Bipolar transsitor, junction field effect transistor (JFET), Mosfet, Photo transistor, Uni junction transistor (UTJ), Silicon control rectifier (SCR), Diac, Triacs outlines ( with their types numbers e.g TO3, TO5, TO18, TO39, TO65 etc) of the different types of semiconductor diodes, Transistors Scrs, Diacs, Triacs and ICs (along with indicators for pin identification etc.)

3. Orthographic projections

Introduction to Orthographic projections. Conversion of pictorial view into Orthographic, Views (First Angle Projection Method Only), Dimensioning technique as per SP-46

4. Isometric projection

For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.

5. Logic gates(With the help of rough sketch/clues given)

Draw standard symbols of NOT, AND, NAND, OR, NOR XOR, Expandable & Tristate gates, Op, Amp, Ic, Flip-flops (Combination of 2,3,4 input gates should be drawn).

6. Graphical Representation of data

General concept, selection of variables & curve fitting, curve indentification zeropoint location. Use of various graph paper and preparation of diagram from given data. Bar charts, pie graph, pictorial graph.

7. Circuit Diagram(With the help of rough sketch/clues given)

For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.

Instructional Strategy:

Teacher should show model of realia of the component/part whose drawing is to be made.Emphasis should be given on cleanliness, dimensioning and layout of sheet. Focus should be on proper selection of drawing instruments and their proper use. Students must use H grade pencils for the first few (10 sheets), till they are familiar with the proper thickness of all type of lines. Relevant IT tools to be used to state that 3D solid modelling, which is to be taught at the starting point. Also how 2D views can be obtained from 3D solid modelling to 2D views rather than the conventional method of making the students visualize the 3D view of an object by mentally constructing it from the 2D views

Means of Assessment:

1. Drawing
2. Assignments and quiz/class tests
3. Mid-term and end-term written tests

Text Books:

1. A Text Book of Engineering Drawing by Surjit Singh; DhanpatRai& Co., Delhi
2. Engineering Drawing by PS Gill; SK Kataria& Sons, New Delhi
3. Elementary Engineering Drawing in First Angle Projection by ND Bhatt; Charotar Publishing House Pvt. Ltd., Anand
4. Engineering Drawing I & II by JS Layall; Eagle Parkashan, Jalandhar
5. Engineering Drawing I by DK Goel, GBD Publication.
6. e-books/e-tools/relevant software to be used as recommended by AICTE/UPBTE/NITTTR.

Reference Books:

1. http://swayam.gov.in
2. http://spoken-tutorial.org

For detail syllabus of all other subjects of BE Computer Science, effective from 2019-2020 do visit Computer Science 1st Sem BTEUP syllabus for 2019-2020.

Dont forget to download iStudy Syllabus App for latest syllabus and results, class timetable and more.