Process Control Instrumentation & Ctrl 6th Sem Syllabus for Diploma BTEUP 2017

Process Control detail BTEUP Diploma syllabus for Instrumentation And Control, effective from 2017 is collected from BTEUP 2017 Syllabus official website and presented for diploma students. The course details such as exam duration, Teaching Hr/week, Practical Hr/week, Total Marks, internal marks, theory marks, duration and credits do visit complete sem subjects post given below. The syllabus PDFs can be downloaded from official website.

For all other instrumentation & ctrl 6th sem bteup diploma syllabus 2017 you can visit Instrumentation & Ctrl 6th Sem BTEUP Diploma Syllabus 2017 Subjects. The detail syllabus for process control is as follows.

Rationale:

To keep output at predesired value some adjustment in process parameters is required during the plant operation. The control actions to be performed are mainly On-Off, proportional, integral and derivative. These control actions can be performed by pneumatic, electric, electronics, hydraulic or mechanical controllers. The controlled variable is finally fed to the final control elements. The students if familiar with different type of controllers, their installation and maintenance will be more suitable to the process industries.

DETAILED CONTENTS

1. INTRODUCTION:

Basic of Process control, Process and process charcteristics, (Static and Dynamic) resistance and capacitance of a process, analog with electrical system, process time delay, dead time process delay in single capacitor and two capacitor process, response of general control process in following diagram of a general closed loop process control system.

2. AUTOMATIC CONTROL ACTIONS:

For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.

3. PNEUMATIC AND HYDRAULIC CONTROLLER:

Flapper-Nozzle system as control element, characteristic of flapper-nozzle system, Effect of non linearity of various gain, direct active and reverse acting relay as amplifier in
pneumatic system. On/Off, P, PI, PD and PID pneumatic controller, Hydraulic fluids, Jet nozzle as control component comparision between hydraulic and pneumatic
control system. Hydraulic controller (On/Off, P, PI, PD and PID type).

4. ELECTRONIC CONTROLLERS:

Opamp as building block of Elex controller, On/Off, P, PI, PD, PID, Elex. Controller. Types of controllers cascade & Ratio controller

5. DIRECT DIGITAL CONTROL SYSTEM :

For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.

6. PROGRAMMABLE LOGIC CONTROLLER (PLC) :

Introduction, Principle of operation, Architecture of programmable controller, Programming the programmable controller, Application of programmable controller. Types of PLC programming, Ladder & Bolean logic

7. DISTRIBUTED CONTROL SYSTEM (DCS) :

Real time computer control system – A concept, Functional requirements of distributed process control system, System architecture, Distributed control system, Configuration, Some popular DCS. DCS configuration and working, Types and Characteristics of control valves, Seat leakage class of Control valve, Installation and maintenance of control valves.

8. FINAL CONTROL ELEMENT :

For complete syllabus and results, class timetable and more pls download iStudy Syllabus App. It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.

9. PREVENTIVE MAINTENANCE:

Objectives of preventive maintenance, elements of preventive maintenance,Procedure of preventive maintenance, simple example of preventive programmes and maintenance schedules.

10. VIRTUAL INSTRUMENTATION :

Concept of data flow techniques, basics of data acquisition and use of analysis tools.

PROCESS CONTROL LAB:

1. To draw characteristic of
1. Quick opening control valve
2. Equal percentage control valve
3. Linear control valve
2. To draw the characteristic of valve
1. Without positioner
2. with valve positioner and compare it
3. To study the working of D/P transmitter and plot the I/o characteristic at different range of I/P span.
4. To study the working of ON/OFF level controller and draw I/O characteristics.
5. To study the PLC ladder logic and do various experiment of given PLC.
6. To fabricate an allication circuit using PLC and Various sensors and write a program to operate it in various way.
7. To study PC/PLC based multiprocess control system using training module.
8. To study a distributed control system pannel and do various experiment task on it.
9. To design a simple control diagram on SCADA software and link it to a given PLC and do various experiment on it.
10. Design a control loop of a typical process using LABVIEW and do various task using using virtual instrumentation software.
11. To fabricate and install a process instrumentation system.

For detail syllabus of all other subjects of BE Instrumentation & Ctrl, effective from 2017 do visit Instrumentation & Ctrl 6th Sem BTEUP syllabus for 2017.

Dont forget to download iStudy Syllabus App for latest syllabus and results, class timetable and more.