AEDLO5013: Design of Jigs and Fixtures Syllabus for AE 5th Sem 2018 Pattern Mumbai University (Department Level Optional Course-1)

Design of Jigs and Fixtures detailed syllabus scheme for Automobile Engineering (AE), 2018 regulation has been taken from the MU official website and presented for the Bachelor of Engineering students. For Course Code, Course Title, Test 1, Test 2, Avg, End Sem Exam, Team Work, Practical, Oral, Total, and other information, do visit full semester subjects post given below.

For 5th Sem Scheme of Automobile Engineering (AE), 2018 Pattern, do visit AE 5th Sem Scheme, 2018 Pattern. For the Department Level Optional Course-1 scheme of 5th Sem 2018 regulation, refer to AE 5th Sem Department Level Optional Course-1 Scheme 2018 Pattern. The detail syllabus for design of jigs and fixtures is as follows.

Design of Jigs and Fixtures Syllabus for Automobile Engineering TE 5th Sem 2018 Pattern Mumbai University

Course Outcomes:

For the complete Syllabus, results, class timetable, and many other features kindly download the iStudy App
It is a lightweight, easy to use, no images, and no pdfs platform to make students’s lives easier.
.

Module 1

Introduction to Tool Design Production Toolings Jigs, Fixtures and their difference, their requirement(accuracy, machinability, quantity modifications so as toassist production, Interchange ability, Simplicity, Swarf disposal,Handling, Ease of operation, Skill reduction, Cost reduction), Analysis forOperation planning, sequencing of operations. 08

Module 2

Basic Construction of Jig & Fixture

Location & Locating Devices Locating principles: Degrees of freedom, Redundant location, Fool-proofing, nesting, Locators: locators that control work piece on flat surfaces, location of cylindrical surfaces, conical locators, centralizers.
Clamping & clamping Devices Requirement of clamping system, Position of clamps, Types of clamps, Clamping devices; examples of typical clamps(multiple clamping and equalizing devices, quick acting clamping mechanisms such as link, toggle, cam, eccentric, pneumatic, hydraulic and electric devices), Component distortion under clamping and cutting forces, Material used for different clamping devices of jigs/fixture and recommended hardness 10

Module 3

Module 4

Construction of Milling fixture Introduction, Selection of location, supporting and clamping faces /points choice, tool setting block and Tennons, Case Study on Design of Milling Fixture 08

Module 5

Introduction to Commonly used Fixtures Turning Fixture (Chucks, collets, Mandrels) Grinding Fixture, BroachingFixture, and Welding Fixture 08

Module 6

Assessment:

Internal Assessment for 20 marks: Consisting Two Compulsory Class Tests First test based onapproximately 40% of contents and second test based on remainingcontents (approximately 40% but excluding contents covered in Test I) End Semester Examination: Weightage of each module in end semester examination will be proportional to number of respective lecture hours mentioned in the curriculum.

Question paper will comprise of total six questions, each carrying 20 marks
Question 1 will be compulsory and should cover maximum contents of the curriculum
Remaining questions will be mixed in nature (for example if Q.2 has part
1. from module 3 then part
2. will be from any module other than module 3)
Only Four questions need to be solved

Reference Books:

Jig and Fixture Design Manual, Erik K. Henrikson, Industrial Press
An introduction to jig and tool Design, MH A Kempster, 3rd Edition, ELBS
Jigs and Fixture, P. H. Joshi, TMH
Tool design, C. Donaldson, George H. Lecain, V.C. Goold, TMH
Jigs and Fixture Handbook, A.K. Goroshkin, Mir Publication
Jigs and Fixture, ASTME
Non- Standards Calming Devices, Hiran E. Grant TMH, New Delhi

For detail Syllabus of all subjects of Automobile Engineering (AE) 5th Sem 2018 regulation, visit AE 5th Sem Subjects of 2018 Pattern.

InI MH