Basic Electrical and Electronics Engineering detailed Syllabus for Computer Science & Engineering (CW), K scheme PDF has been taken from the MSBTE official website and presented for the diploma students. For Subject Code, Subject Name, Lectures, Tutorial, Practical/Drawing, Credits, Theory (Max & Min) Marks, Practical (Max & Min) Marks, Total Marks, and other information, do visit full semester subjects post given below.
For all other MSBTE Computer Science & Engineering 2nd Sem K Scheme Syllabus PDF, do visit MSBTE Computer Science & Engineering 2nd Sem K Scheme Syllabus PDF Subjects. The detailed Syllabus for basic electrical and electronics engineering is as follows.
Rationale
For the complete Syllabus, results, class timetable, and many other features kindly download the iStudy App
It is a lightweight, easy to use, no images, and no pdfs platform to make students’s lives easier.
.
Course Outcomes:
Students will be able to achieve & demonstrate the following COs on completion of course based learning
- Calculate and measure basic electrical quantities and parameters.
- Use different electrical machines by making connections.
- Use electrical safety devices in electrical circuit
- Use relevant diode in different electronic circuits.
- Use BJT and FET in various electronic circuits.
- Use various types of sensors and transducers.
Unit I
Basic Electrical Fundamentals 1.1 Electric and magnetic circuits. 1.2 Series and parallel magnetic circuits. 1.3 Faraday’s laws of electromagnetic induction, Fleming’s right hand rule,Lenz’s law 1.4 Dynamically and statically induced emf, self and mutual inductance 1.5 AC and DC quantity, advantages of AC over DC supply. 1.6 Single phase AC, sinusoidal AC wave: instantaneous value, cycle, amplitude, time period, frequency, angular frequency, RMS value, Average value for sinusoidal waveform, form factor, peak factor. 1.7 Three phase supply system over single phase supply system, Phase sequence and balanced and unbalanced load 1.8 Star and delta connections, Phase and line current, phase and line voltage in star connected and delta connected balanced system. Chalk-Board Presentations Demonstration
Unit II
For the complete Syllabus, results, class timetable, and many other features kindly download the iStudy App
It is a lightweight, easy to use, no images, and no pdfs platform to make students’s lives easier..
Unit III
Electrical Safety and Protective Devices. 3.1 Low rating Fuse: Operation, types 3.2 Switch Fuse Unit and Fuse Switch Unit: Differences, use of multimeter for electrical quantities/ parameters measurements. 3.3 MCB and ELCB/RCB: Operation and general specifications 3.4 Earthing: Types, Importance of earthing, factors affecting eatthing resistance. 3.5 Measures for reducing earth resistance, I.E rules relevant to earthing. Chalk-Board Demonstration Presentations
Unit IV
Special purpose diodes and their applications. 4.1 Zener diode: working, symbol, applications. 4.2 LED: working, symbol, applications. 4.3 Filters: Need for filters, circuit diagram and working of L, C and CLC filter. 4.4 Working principle and block diagram of regulated power supply. 4.5 UPS: Block diagram of Online and Offline UPS. Chalk-Board Demonstration Assignment
Unit V
For the complete Syllabus, results, class timetable, and many other features kindly download the iStudy App
It is a lightweight, easy to use, no images, and no pdfs platform to make students’s lives easier..
Unit VI
Sensors and Transducers 6.1 Sensors and Transducers: Basic definition, difference, classification. 6.2 Thermal, Optical, Electric sensors 6.3 Transducers: Need of transducer, types of transducers: Primary, Secondary, Active, Passive, Analog, Digital 6.4 Selection criteria of transducer Chalk-Board Demonstration Assignments
Practical / Tutorial Experiences
- Measure the parameters of simple electrical and identify presence of flux lines in magnetic circuit.(e.g. current, voltage, power, flux)
- Measure frequency, time period, rms value, peak value of sinusoidal AC waveform for resistive and inductive circuit using CRO.
- Phase difference of voltage and current in inductive circuit.
- Measure the line voltage, phase voltage and phase current and line current in three phase star connected balanced load.
- Measure the line voltage, phase voltage and phase current and line current in three phase delta connected balanced load.
- Determination of the voltage and current ratio of single phase transformer.
- Operate DC shunt motor by connecting three point starter.
- Operate DC series motor by connecting three point starter
- Reverse the direction of rotation of universal motor.
- Demonstrate the operation of stepper motor for various speed rotation.
- Use multimeter for measurement of voltage, current (AC,DC), resistance and continuity of the given electrical circuit.
- Connect fuse in electrical circuit and check its operation at normal and abnormal conditions.
- Connect MCB in electrical circuit and check its operation at normal and abnormal conditions.
- Connect ELCB in electrical circuit and check its operation at normal and abnormal conditions.
- Use of earth tester for meaurement of earthing resistance of a installed earthing of laboratory.
- Connect the Zener diode in the circuit and test its operation in forward and reverse bias mode.
- Determine the voltage regulation by using Zener diode under variable input and output conditions.
- Check the output waveform of L, C and π filters on CRO of rectifier circuit.
- Make the input and output connections of UPS and measure the output voltage under online and offline mode.
- Make the input, output connections and check the operation of UPS under normal and overload condition.
- Test input /output characteristics of NPN transistor in CE configuration.
- Test input /output characteristics of NPN transistor in CB configuration.
- Check the switch ON and switch OFF condition of LED by using transistor.
- Determine the Drain and Transfer characteristics of FET.
- Measure temperature of liquid using RTD (PT-100) transducer.
- Measure temperature of liquid using thermocouple measurement.
- Check the motion of given object using photoelectric sensor.
- Measure the resistance of LDR in varying light intensity.
- Measure displacement using LVDT.
- Measurement of displacement using potentiometer.
Suggested Micro Project / Self Learning
For the complete Syllabus, results, class timetable, and many other features kindly download the iStudy App
It is a lightweight, easy to use, no images, and no pdfs platform to make students’s lives easier..
Laboratory Equipment/Software Required
- Single Phase Transformer: 1kVA, single-phase, 230/150 V, air cooled 6
- Single phase auto transformer (Dimmer stat) – 0-230 volt 2/5Amp 6,13
- CRO – 20 MHz. Dual channel 2,3,18
- Three phase Auto Transformer -10/5 kVA, Input 415 V 3 phase. 50 Hz. Output 0415 V, 10/20 A 4,5
- Rheostat (0-500 Ohm, 1.2A), Nichrome wire wound rheostat on epoxy resin or class F insulating tube with two fixed and one sliding contact 7
- Rheostat (0-100 Ohm, 5A), Nichrome wire wound rheostat on epoxy resin or class F insulating tube with two fixed and one sliding contact 8
- DC Ammeter range (0-5-10A), Portable analog PMMC type as per relevant BIS standard 7
- DC series and shunt machines at least one each (up to 230 V, 3/5 HP). 7,8
- D. C. Supply, A 230 V d.c. supply ( with inbuilt rectifier to convert a.c.to d.c) 7,8
- DC Voltmeter Range (0-150/300V), Portable analog PMMC type as per relevant BIS standard. 7,8
- AC Ammeter range (0-2.5-5-10A), Portable analog MI type as per relevant BIS standard 5,6,13,14
- AC Voltmeter Range (150/300/600V), Portable analog MI type as per relevant BIS standard 5,6
- Lamp Bank load -230 V 0-10 A 13,14
- Tachometer, noncontact type 0-10000rpm 7,8,9,10
- Single phase Universal motor -1/4 or 1/2 HP ,230 V 9
- Earth tester analog/digital type 15
- Variable DC power supply 0-30V, 2A, SC protection, display for voltage and current. 16,17,21,22,23,24
- Digital Multimeter: 3 1/2 digit 1,16,17,21,22,23
- Electronic Work Bench: Bread Board: 840 tie points, Withstanding Voltage: 1,000V AC, Positive and Negative power rails on opposite side of the board, connecting wires. 16,17,18,21,22,23,24
Suggested Learning Materials
- Theraja, B. L. Theraja, A. K. A Text Book of Electrical Technology Vol-I S.Chand and Co. New Delhi 2014 ISBN: 9788121924405
- Mittle, V. N. Basic Electrical Engg. Tata McGraw-Hill, New Delhi ISBN : 978-0-070088572-5
- Sedha R.S. Applied Electronics S. Chand, New Delhi,2015 ISBN:9788121927833
- Hughes, Edward Electrical Technology Pearson Education, New Delhi ISBN-13: 9780582405196
- V.K. Mehta Principles of Electronics S.Chand and Co Ram Nagar, New Delhi-110055,11th edition 2014 ISBN 9788121924504
- Saxena, S. B. Lal Fundamentals of Electrical Engineering Cambridge University Press, New Delhi ISBN : 9781107464353
- Jegathesan, V. Basic Electrical and Electronics Engineering Wiley India, New Delhi 2014 ISBN : 97881236529513
- Boylestad, Robert Nashelsky Louis Electronic Devices and Circuit Theory Pearson Education. New Delhi 2014 ISBN:9780132622264
- Sawhney A.K. Electrical and Electronic Measurements and Instrumentation Dhanpat Rai and Sons, New Delhi,2005, ISBN:13-9788177000160
- Kalsi H.S. Electronic Instrumentation McGraw Hill, New Delhi,2010 ISBN:13-9780070702066
Learning Websites & Portals
For the complete Syllabus, results, class timetable, and many other features kindly download the iStudy App
It is a lightweight, easy to use, no images, and no pdfs platform to make students’s lives easier..
For detail Syllabus of all other subjects of Computer Science & Engineering, K scheme do visit Computer Science & Engineering 2nd Sem Syllabus for K scheme.
For all Computer Science & Engineering results, visit MSBTE Computer Science & Engineering all semester results direct links.