{"id":24642,"date":"2020-02-24T13:11:07","date_gmt":"2020-02-24T13:11:07","guid":{"rendered":"https:\/\/www.inspirenignite.com\/anna-university\/32055-process-automation-practical-automobile-5th-sem-syllabus-for-diploma-tndte-m-scheme\/"},"modified":"2020-02-24T13:11:07","modified_gmt":"2020-02-24T13:11:07","slug":"32055-process-automation-practical-automobile-5th-sem-syllabus-for-diploma-tndte-m-scheme","status":"publish","type":"post","link":"https:\/\/www.inspirenignite.com\/anna-university\/32055-process-automation-practical-automobile-5th-sem-syllabus-for-diploma-tndte-m-scheme\/","title":{"rendered":"32055: Process Automation Practical Automobile 5th Sem Syllabus for Diploma TNDTE M Scheme"},"content":{"rendered":"

Process Automation Practical detail TNDTE Diploma syllabus for Automobile Engineering (AU), M scheme is extracted from TNDTE<\/a> official website and presented for diploma students. The course code (32055), and for exam duration, Teaching Hr\/week, Practical Hr\/week, Total Marks, internal marks, theory marks, duration and credits do visit complete sem subjects post given below. The syllabus PDFs can be downloaded from official website.<\/p>\n

For all other automobile 5th sem syllabus for diploma m scheme tndte you can visit Automobile 5th Sem Syllabus for Diploma M Scheme TNDTE Subjects<\/a>. The detail syllabus for process automation practical is as follows.<\/p>\n

Rationale:<\/h4>\n<\/p>\n

Objective:<\/h4>\n

Note:<\/b> All the experiments should be conducted. Two questions will be given by selecting one question from each part. Necessary safety arrangement to be made to lift and carryout the experiments. The components should be fixed in the frame \/ table as per the requirement.<\/b><\/p>\n

Part A<\/strong>
\n<\/p>\n

    \n
  1. Remove and replace the pressure plate and clutch plate, fingers adjustment and clutch plate relining.<\/li>\n
  2. Dismantle, inspect and assemble the sliding mesh gear box \/ constant mesh gear box to find the gear ratios.<\/li>\n
  3. <\/li>\n
  4. Dismantle and assemble the rear axle and adjust wheel bearing.<\/li>\n
  5. Dismantle, assemble and adjust the steering gearbox and find gear ratio.<\/li>\n
  6. Dismantle, assemble the power steering.<\/li>\n<\/ol>\n

    \nPart B<\/strong>
    \n<\/p>\n

      \n
    1. Remove, inspect and refit the shock absorber.<\/li>\n
    2. Dismantle and assemble the leaf and coil spring.<\/li>\n
    3. Overhauling, adjusting and bleeding of Hydraulic system.<\/li>\n
    4. Remove the tyre for Vulcanizing the tubes and refit.<\/li>\n
    5. Check, measure and adjust the caster, chamfer, king pin inclination, toe-in and toe- out<\/li>\n
    6. Remove the wheel from the vehicle and balance the wheel using wheel balancing machine<\/li>\n<\/ol>\n

      Board Examination – Detailed Allocation<\/h4>\n

      For complete syllabus and results, class timetable and more pls download iStudy Syllabus App<\/a>.<\/b> It’s a lightweight, easy to use, no images, no pdfs platform to make students life easier.<\/p>\n

      Resources required <\/b>for 32156 Automobile Chassis and Transmission Practical<\/h4>\n

      Minimum requirement for 60 in-take. The facility should be kept based on the intake.<\/strong><\/p>\n

      \nFor each experiment separate components are required.<\/p>\n